One of the most important settings on any serial link is the baud rate — often called the Modbus over RS485 communication frequency. It sets how fast data moves across the bus, and it drives three things you care about on site: how far the cable can run, how many devices you can poll per second, and how… Read More: Modbus over RS485 Communication Frequency and Baud Rate »
In a DNP3-based SCADA system, system topology refers to the physical and logical arrangement of how master stations, outstations, and communication devices are connected and interact. Designed for flexibility and reliability, DNP3 supports multiple network configurations that can be tailored to the system size, communication medium, and redundancy requirements. The most common DNP3 topologies include master–slave, multidrop, hierarchical,… Read More: DNP3 System Topology Explained: Master, Multidrop, and Hierarchical »
Before any data or command exchange can begin, the communication link between the controlling station (master) and controlled stations (RTUs or substation gateways) must be properly established. This process — called link initialization — ensures both sides start from a synchronized state with correct frame sequencing, clear buffers, and ready communication paths. Link initialization is part of the… Read More: Link Initialization in IEC 60870-5-101 | Master-Slave Communication Setup »
The IEC 60870-5-101 protocol (commonly known as IEC 101) is a serial telecontrol standard widely used in SCADA, power automation, and industrial control systems. It defines how data is formatted and transmitted between a controlling station (master) and controlled stations, such as RTUs or dedicated substation operation and data-handling devices. Each message on the line is called a… Read More: IEC 101 Frame Formats Explained | Fixed & Variable Frames »
The Originator Address in IEC 60870-5-101 is an optional but powerful feature that enhances message routing and command traceability in telecontrol and SCADA systems. This one-byte field, located within the Cause of Transmission (COT) section of the ASDU, allows a controlling station to explicitly identify itself when sending commands. In systems with a single master station, this feature… Read More: Originator Address in IEC 60870-5-101 Explained »
IEC-60870-5-101 (IEC-101) and IEC-60870-5-104 (IEC-104) are two of the most important communication protocols used in electrical power systems, especially in substations and national SCADA systems. Both belong to the IEC-60870-5 family, which defines how remote telecontrol data is exchanged for monitoring, supervision, and automation. Even though the two protocols share the same information structure (ASDUs), they behave very… Read More: IEC-101 vs IEC-104 — Key Differences Explained »
DNP3 (Distributed Network Protocol) messages are built in multiple layers to ensure reliable communication between master stations and outstations (RTUs or IEDs) in SCADA systems. Each layer adds its own control information, creating a message that can be verified, retransmitted, and correctly interpreted across noisy or unreliable communication links. The Enhanced Performance Architecture (EPA) DNP3 follows the IEC… Read More: DNP3 Message Structure Explained »
Modern critical infrastructure systems — such as electric utilities, water treatment, and oil & gas networks — rely heavily on SCADA communications to monitor and control field equipment. One of the most trusted communication standards enabling this exchange is the Distributed Network Protocol version 3 (DNP3). While DNP3 was originally designed for reliability and efficiency, its early versions… Read More: DNP3 Secure Authentication Version 5 (SAv5): Strengthening SCADA Communication Security »
In Distributed Network Protocol (DNP3), the Internal Indications field—commonly known as IIN—plays a fundamental role in real-time SCADA diagnostics. Whether you’re troubleshooting substation RTUs, assessing communication integrity, or analyzing unsolicited events, DNP3 IIN bits provide the device’s internal status and operational health. This article explains DNP3 IIN bits in depth, their function in DNP3, how Wireshark displays them,… Read More: DNP3 IIN (Internal Indications) Bits Meaning & SCADA Troubleshooting Guide »
Wireshark is the go-to tool for analyzing communication protocols — and it fully supports IEC 60870-5-104 (commonly known as IEC 104). Whether you’re diagnosing network issues, validating SCADA data, or learning how IEC 104 works, Wireshark provides an unmatched level of visibility into the protocol’s Ethernet, TCP, and ASDU layers. This guide shows you how to capture, decode,… Read More: Wireshark IEC 60870-5-104 Decoding — Analyze SCADA Communication in Depth »